Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
EPC of Power Plants 40 MW CPP at ISMT Limited, Chandrapur, Maharashtra Commissioned in Dec 2011. Our 40 MW CPP at Maharashtra is powered by a 170 tph AFBC boiler (89ata, 520 °C) designed for firing grade D and grade F Indian Coal. Shell and Tube type water cooled condenser is installed for condensing the steam turbine generator exhaust.
A 440 MW coal-fired power plant is 40% efficient at producing electricity.The coal has a heating value of 20,000 kJ/kg, an ash content of 6.0%, and asulfur content of 4.0% . a.What is the daily input rate of coal (kg/day)?. b.If the overall efficiency of ash capture is 98.6%, how much ash is …
this effort from data in NEEDS v4.10 of boiler heat rate versus capacity for all pulverized coal or cyclone boilers. As shown, heat rate is highest for small boilers and lowest for large boilers, and this is worth examining further. 3. Facility age. 5 Even within a cycle type (i.e., supercritical versus subcritical), there have been advances in
AFBC Boiler Working Principle: Technological collaboration with Power Systems for boilers up to 300 TPH. There are more than AFBC boilers operating worldwide which were designed as per Power System design and supplied either directly produced by their licensees. AFBC Boiler Salient Features: Low fluidizing velocity for lower wear of bed tubes.
1 kWh of net electrical energy output. It is the metric most often used in the electric power generation industry to track and report the performance of thermal power plants. The average, annual operating heat rate of U.S. coal-fired power plants is approximately 10,400 Btu/kWh. The design heat rate of a facility is based on full-load operation
This article talks about coal fired power plant boiler with the output capacity of 10MW.The 10 MW coal fired power plant boiler is based upon coal fired circulating Fuel Bed (CFB) technology, in which the boiler-based power generation is as the preferred fuel/cycle combination for power generation. More than half of the electricity generated in the world is by using coal as the primary fuel.
Comm. supervisor-(Daelim Saudi arabia Co.Ltd) ISS shared Operation of Gas fired boiler-35TPH (Fire tube Boiler-Thermax)& HFO/HSD fired boilers. Cooling Commissioning & Operation Of Power Plant 2 x20= 40 MW (Captive Power Plant) 2 X 90 TPH AFBC Coal fired High Pressure Boilers- IJT Boilers.
At present 54.09% or 93918.38 MW (Data Source CEA, as on 31/03/2011) of total electricity production in India is from Coal Based Thermal Power Station. A coal based thermal power plant converts the chemical energy of the coal into electrical energy.
Because PFBC operates at a higher pressure and increased efficiency compared with AFBC, the same power output can be achieved with a unit that requires less land area (i.e., smaller "footprint" of equipment). A commercial order also has been placed for SCR on a 285-MW coal-fired plant operated by an independent power producer (Makansi
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292Get Latest Price
Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.