Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
High Pressure Coal Boiler (GregTech 4) High Pressure Coal Boiler (GregTech 5) This disambiguation page lists articles associated with the same title. If an internal link led you here, you may wish to change the link to point directly to the intended article.
Blast resistance: 10 Jan 15, 2019· If the sand or limestone in a fluidized state is heated to the ignition temperature of the coal and the coal is injected continuously into the bed, the fuel will burn rapidly and the bed attains a uniform temperature due to effective mixing. The fluidized bed combustion takes place at a temperature of 840°C to 950 °C.
High Furnace Pressure in Boiler. Combustion in a boiler furnace is normally considered a controlled explosion, as all boilers operate at a regime where explosion pressure is the maximum. This is mainly due to the fact that it is at this regime we get the maximum efficiency of the boiler. Furnace pressure in boilers is one of the most critical and important parameter to be maintained and monitored.
This would happen if water entered the boiler at a pressure above the critical pressure (3,206 pounds per square inch, 22.10 MPa); was heated to a temperature above the critical temperature (706 °F, 374 °C) and then expanded (through a simple nozzle) to dry steam at some lower subcritical pressure.
This is the largest and most important pressure part in the boiler and weighs in the range 250 Tons for 600 MW power plant. Water Walls Boiling takes place in the ‘Water Walls’ which are water filled tubes that form the walls of the furnace.
Boilers are classified also by their pressure capacity, design type and use. Maximum allowable working pressure, or MAWP, is the highest amount of pressure that the vessel (boiler) is designed to withstand. This pressure is measured in terms of pounds per square inch or “psi,” and gauge pressure …
coal fired boiler The Coalmiser HPD (High Pressure) design is suitable for applications to produce high pressure steam or hot water in ranges from 5,000 - 40,000 lbs/hr (4.8 mm BTU - 39 mm BTU) output from 150 up to 250 PSI.
Our engineers developed an automatic stoker unit equipped with a coal hopper that held enough fuel for several days. This allowed the coal to be cleanly burned and without frequent maintenance. They then saw the need to make a hot water boiler specifically designed to burn coal and built them in multiple sizes to meet our customers’ needs.
Oct 08, 2019· The High Pressure Coal Boiler is therefore the most fuel efficient Coal-burning GregTech generator. The boiler can hold 32,000 Liters of steam and 16,000 Liters of water. As long as its temperature is above 100, every 10 ticks it will consume 1 Liter of water and produce 150 Liters of steam, equivalent to 15 mB/t of steam.
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292Get Latest Price
Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.