Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
the ASME Boiler and Pressure Vessel Code. Whenever local customary units are used the Manufacturer shall provide the source of the conversion factors, which shall be subject to verification and acceptance by the Authorized Inspector. Material that has been manufactured and certified to …
According the "ASME Boiler and Pressure Vessel Code" boilers may be classified asSection I Power Boilers - process boilers, power boilers and high pressure boilers. boilers in which steam or other vapor is generated at a pressures exceeding 15 psig ; high temperature water boilers intended for operation at pressures exceeding 160 psig and or temperatures exceeding 250 degrees F
Entire code is always current. The Register date on each page is the date the chapter was last published. Register May 2012 No. 677 Chapter SPS 341 APPENDIX A EXCERPTS FROM: ASME BOILER AND PRESSURE VESSEL CODE SECTION I − POWER BOILERS 2010 EDITION INTRODUCTION This Code covers rules for construction of power boilers1,
The ASME Code Section 8 is the construction code for pressure vessel and covers design, manufacturing and pressure vessel inspection and testing in the manufacturing shop. This Code section addresses the mandatory requirements, specific prohibitions, and non-mandatory guidance for Pressure Vessel Materials, design, fabrication, examination
Section IX of the ASME BPVC. ASME P-Numbers. Structural Welding . Section IX of the ASME Boiler and Pressure Vessel Code Overview. The forms listed below form the basis for verifying welding procedures and welder performance: WPS - welding procedure specification PQR - procedure qualification record WPQ - welder performance qualification
Sep 25, 2019· Summary of ASME BPVC Section IX – Part 1 February 18, 2019 September 25, 2019 Sandeep Anand 5 Comments ASME Boiler and Pressure Vessel Code (BPVC), Section IX contains qualification standard for the following;
File Size: 1MB MacKay, John R., and Pillow, James T. "Piping Design." Power Boilers: A Guide to the Section I of the ASME Boiler and Pressure Vessel Code, Second Edition. Ed. John R
Full text of "ASME BPVC V (2010): Boiler and Pressure Vessel Code, Part V, Nondestructive Examination" See other formats
The 2010 ASME Boiler and Pressure Vessel Code with Addenda Improving Public Safety and Facilitating Global Trade Section I- Power Boilers Has rules for construction of power, electric, and miniature boilers; high temperature water boilers for stationary service; and power boilers for locomotive, portable, and traction service. Spanish-
Code Books Required for Use with ASME Product Certification Marks Note: For books other than the Boiler & Pressure Vessel Code (e.g., B31.1, PTC 25, NQA-1), the required edition as of July 1, 2013 is listed. The specific effective Addenda will be referenced …
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292Get Latest Price
Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.