Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
High-pressure spray water is used to sluice bottom ash and pyrites from the boilers’ hopper bottoms and to carry the ash out of the plant. The valves used are typically ANSI Class 300 double
Nov 28, 2017· When operational, the plant will be the largest solar PV plant in Nigeria; and one of the largest on the African continent. The 75MWac output to the grid is expected to serve approximately 1.1
A boiler or steam generator is a device used to create steam by applying heat energy to water.Although the definitions are somewhat flexible, it can be said that older steam generators were commonly termed boilers and worked at low to medium pressure (7–2,000 kPa or 1–290 psi) but, at pressures above this, it is more usual to speak of a steam generator.
There are currently two main types of power plants operating in Nigeria: (1) hydro-electric and (2) thermal or fossil fuel power plants. With a total installed capacity of 8457.6MW (81 percent of total) in early 2014, thermal power plants (gas-fired plants) dominates the Nigerian power supply mix. Electricity production from hydroelectric sources (% of total) in Nigeria was reported at 17.59%
Practical Boiler Operation Engineering Power plants by Amiya Ranjan Mallick. The book covers the entire cross-functional aspects of a thermal power plant. Some basic concepts of engineering related to power plants are discussed in Chapters 1, 2, 3 and 4. Water chemistry which is very important for a boiler is discussed in Chapter 5. From …
The above are the major water and steam circuit items in a boiler and are collectively called the ‘pressure parts’. This post is part of the series: Working Of A Power Plant Boiler. Boiler in a power plant has two functions. The Combustion system converts energy in coal to Heat.
Types of Boilers Used in Power Plants 2017-07-31 17:31:22 . A power plant or a power generating station, is basically an industrial location that is utilized for the generation and distribution of electric power in mass scale, usually in the order of several 1000 Watts.
Nigeria with a population of well over 170 million people derives her bulk electricity supply from both Hydro and Thermal power plants. The plants, located in different parts of the country should
Kainji power station reservoir. Kainji power station is hydro-electric powered. It has an installed … The power plant is located near its customers’ base and natural gas feedstock. 7. Egbin Power Plc. Egbin Power Plc operates the Egbin Power Station Complex which is the largest power generating thermal plant in Nigeria. The power station has an installed generating capacity of 1,320MW.
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292Get Latest Price
Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.