Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
Aug 10, 2017· The change in fuel usage suggest that there is an issue with the boiler, though you do want to rule out any others differences (ambient temp, people in …
For over 46 years, Superior Boiler has constructed complete renewable energy systems using biomass as a fuel source. It is Superior Boiler’s philosophy that in order for the United States to reduce its dependency on foreign oil, it must take advantage of its many renewable, natural and …
A time delay relay is a way to squeeze the most heat out of your system without running the boiler. When the thermostat clicks on, the relay causes the boiler to circulate hot water through the system without turning on the boiler. After a set time, the boiler will fire up. A time delay relay costs about $100 and can cut your fuel costs by up
Mar 17, 2015· Steam, Boiler, and Blowdown Pressure are the same. Combustion Efficiency is the % of fuel energy that is directly added to the feedwater and not otherwise lost or used. Blowdown Rate is the % of incoming feedwater mass flow rate that leaves the boiler as a saturated liquid at boiler pressure.
May 07, 2017· Steam atomization is used in oil burners to assist the mixing of oil and air to promote full combustion. With steam injection, the oil is reduced to a fine spray that mixes with air and burns easily. The result is a flame that is short and intense
Aug 19, 2019· Boilers can be designed to burn a specific fuel, using any number of different technologies, but the main component to consider here is the heat source, or otherwise known as the fuel. The fuel is one of the most important aspects of a boiler and is what burns inside the boiler to generate the heat.
This is another Alternative Heating & Supplies episode on swimming pool setup and in this blog post we are going to talk about how you can hook up the boiler to the swimming pool, the difference between chlorine and salt water pools, and the difference between using CPVC and PVC in pools. Find out all the details you need to know to use a boiler to heat up your pool water. Continue reading →
Residual oil Crude oil and fuel oil Nos. 1 and 2 that have nitrogen content greater than 0.05 wt %, and all fuel oil Nos. 4, 5, and 6 as defined in ASTM D 396 (Refs. 2 and 5). Solvent-derived fuel Any solid, liquid, or gaseous fuel derived from solid fuel for the purpose of creating
Specifically, AFUE is the ratio of annual heat output of the furnace or boiler compared to the total annual fossil fuel energy consumed by a furnace or boiler. An AFUE of 90% means that 90% of the energy in the fuel becomes heat for the home and the other 10% escapes up the chimney and elsewhere.
The efficiency of a boiler is measured as AFUE (annual fuel utilization efficiency), which is the ratio of annual heat output of the boiler compared to the total annual fuel energy consumed by the boiler.
Otherwise, there are no significant changes or modifications to observe for using biodiesel blends in your boiler. Biodiesel works well in residential as well as large scale commercial boilers. Because biodiesel has a higher flash point than #2 diesel fuel, a pre-heater is recommended, but not absolutely necessary. Our first boiler was a
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292Get Latest Price
Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.