Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
Instatherm · Calculators · Contact Us · Air Preheaters · What is Boiler The National Fire Prevention Association and federal standards define a Type II steam boiler as one that produces high-pressure steam between 16 and 150 psig. A Type III steam boiler produces steam between 151 and 350 psig.
Oct 27, 2016· A boiler is called a high-pressure boiler when it operates with a steam pressure above 80 bars. The high-pressure boilers are widely used for power generation in thermal power plants. In a high-pressure boiler, if the feed-water pressure increases, the saturation temperature of water rises and the latent heat of vaporization decreases.
The industrial watertube boiler (Type D, O, or A) is primarily a steam boiler used for various process applications requiring higher pressures, large quantities of steam, and the possibility of additional heat through integrally mounted superheaters.
High-pressure boilers are typically used for process loads and can have an operating pressure of 16 to more than 1,000 psig. Most steam boiler systems require saturated steam, which means the water and the steam in the vessel are at the same temperature.
A water tube boiler can be defined as a Steam boiler in which the flow of water in the tubes, as well as hot gases, enclose the tubes. Not like fire tube boilers, this boiler attains high-pressures, as well as high-steam capabilities, can be achieved. This is because of condensed tangential pressure on tubes which is known as hoop stress.
With multiple pressure designs, the water tube boilers can meet the steam supply requirements of 2.5MPa or above. The fire tube boilers, on the contrary, are intended for use at pressures below 2.5 MPa. Fire tube boilers usually have a capacity of below 20t/h, while water tube ones of 20t/h or more as capacity expansion is possible.
High pressure boilers ( Powertherm) are mostly water tube boilers in which water is on the tube side while flue gases flow across the tubes thereby transferring heat from flue gases …
In contrast to its internal construction, which includes a small steam drum and small diameter tubes, the water tube boiler is used to generate steam having high pressure and temperature. These small internal parts produce high volume steam for high capacity applications.
Steam generated at high pressure and superheated would be fed to a turbine driving an alternator to generate electricity. Low-pressure steam leaving the turbine would then be used for the process.The smaller water tube boilers can be built at the manufacturers and delivered to site as one unit package water tube boiler.
The boilers are able to heat the water used in bathrooms and use steam to heat the different rooms throughout the building, allowing them to become warm. High-Pressure Boiler Definition High-pressure boilers will heat steam above 15 psi and water at pressures that exceed 160 psig.
A high-pressure steam locomotive is a steam locomotive with a boiler that operates at pressures well above what would be considered normal. In the later years of steam, boiler pressures were typically 200 to 250 psi. High-pressure locomotives can be considered to start at 350 psi, when special construction techniques become necessary, but some had boilers that operated at over 1,500 psi. Delaware & …
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292Get Latest Price
Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.